www.gefen.com®8x1 DVI DL/SL SwitcherEXT-DVI-841DLUser Manual
7 8X1 DVI DL/SL REMOTE DESCRIPTIONLED IndicatorInput SelectionButtonsThe RMT-8IR remote control will allow the user to select which of 8 DVI sources w
8 8X1 DVI DL/SL REMOTE INSTALLATIONTo use the RMT-8IR remote, remove the battery cover on the back of the remote to reveal the battery compartment. In
9RMT-8IR REMOTE AND 8X1 SWITCHER CONFIGURATIONHow to Resolve IR Code Confl ictsIn the event that IR commands from other remote controls confl ict with t
10EDID NOTESWhat is EDID and what is it used for?Under normal circumstances, a computer source device (digital or analog) will require information abo
11EDID NOTES, CONT’DEDID ModesThe diagram below illustrates the DIP switch bank (of 4). The 8 DIP switch bank functions are outlined later on this pag
12DL (Dual Link) Only ModesThe 8 DIP switch bank, located on the underside of the 8x1 DVI DL/SL Switcher cab be used to set each individual input to w
13RS-232 SERIAL CONTROL INTERFACEWhat features are available via the RS-232 serial communications port?The 8x1 DVI DL Switcher can accept commands thr
14RS-232 SERIAL CONTROL COMMANDSRS-232 FeaturesRS-232 remote functions are used to control of this product’s features. Features include input to outpu
15RS-232 SERIAL CONTROL COMMANDS#EDIDDSTOLO FunctionThe #EDIDDSTOLO function reads the downstream EDID and stores into all lo-cal inputs.Syntax:#EDIDD
RS-232 SERIAL CONTROL COMMANDS16#DDCTODS FunctionThe #DDCTODS function routes the input DDC to the downstream EDID (pass-through mode).Syntax:#DDCTODS
ASKING FOR ASSISTANCETechnical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM Monda
17RS-232 SERIAL CONTROL COMMANDS#LOEDIDTOBA FunctionThe #LOEDIDTOBA function loads the specifi ed EDID fi le and stores it in a specifi ed EDID bank.Synt
18RS-232 SERIAL CONTROL COMMANDS#LOEDIDTOLO FunctionThe #LOEDIDTOLO function loads the specifi ed EDID fi le to a specifi ed local input.Syntax:#LOEDIDTO
19RS-232 SERIAL CONTROL COMMANDS#PRDSEDID FunctionThe #PRDSEDID function reads the downstream EDID and sends it to the serial port.Syntax:#PRDSEDID pa
20RS-232 SERIAL CONTROL COMMANDSCommandsSimplifi ed syntax was used for command implementation for faster operation with the device: # character – isn’
21RS-232 SERIAL CONTROL COMMANDS2. USING SHORT-CUT CHARACTERS TO CHANGE SETTINGS2.1 HYPERTERMINALtm SETTINGS in Microsoft WindowstmFirst, please setup
22RACK MOUNT INSTALLATIONRear of unitFront of unitRack mount ears are provided for installation of this unit into a 1U rack mount space.1. Locate the
SPECIFICATIONS23Video Amplifi er Bandwidth:...165 MHz x 2Input Video Signal:...
24WARRANTYGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects
20600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefen.com [email protected] A9PbThis product uses
CONTENTS1 Introduction2 Operation Notes3 Features / Package Includes4 Panel Layout5 Panel Descriptions6 Connecting and Operating the 8x1 DVI DL/SL S
1INTRODUCTIONCongratulations on your purchase of the 8x1 DVI DL/SL Switcher. Your complete satisfaction is very important to us.GefenGefen delivers in
OPERATION NOTES2READ THESE NOTES BEFORE INSTALLING OROPERATING THE GEFEN 8X1 DVI DL/SL SWITCHER• The 8x1 DVI DL/SL Switcher will take any of up to ei
3FEATURESFeatures• EDID Management • Switches easily between any eight DVI-SL or DVI-DL sources• Maintains highest resolution dual link
4PANEL LAYOUTBack PanelFront Panel568942137
5PANEL DESCRIPTIONS1 External IR PortFor connection of external IR extension device such as the Gefen IR Extender (part # EXT-RMT-EXTIR).2 IR Receive
6CONNECTING AND OPERATING THE 8X1 DVI DL/SLHow to Connect the 8x1 DVI DL/SL Switcher to your devices:1. Connect the supplied DVI cables from the DVI
Komentáře k této Příručce