Gefen EXT-DVIKVM-841DL Uživatelský manuál

www.gefen.com®88888888888888888888888888888888x1 DVI KVM DLSwitcherEXT-DVIKVM-841DLUser Manual

7 8X1 DVI KVM DL REMOTE DESCRIPTIOND IndicatorLEDInput SelectionButtonsThe RMT-8IR remote control will allow the user to choose which of 8 DVI sources

8 8X1 DVI KVM DL SWITCHER REMOTE INSTALLATIONTo use the RMT-8IR remote, remove the battery cover on the back of the remote to reveal the battery compa

9RMT-8IR REMOTE AND 8X1 KVM SWITCHER CONFIGURATIONHow to Resolve IR Code Confl ictsIn the event that IR commands from other remote controls confl ict wi

10EDID MODESEDID. What is it, and what is it used for?,Under normal circumstances, a computer source device (digital or analog) will require informati

11EDID MODESEDID ModesThe diagram below illustrates the 4 DIP switch bank. The 8 DIP switch bank functions are outlined later on this page.DIP SWITCHF

12DL (DUAL LINK) ONLY MODESDL (Dual Link) Only Modes()yThe 8 DIP switch bank, located on the underside of the 8x1 DVI KVM DL Switcher cab be used to s

13RS-232 SERIAL COMMUNICATIONWhat features are available via the RS-232 serial communications port?pThe 8x1 DVI KVM DL Switcher can accept commands th

14RS-232 SERIAL CONTROL COMMANDSRS-232 FeaturesRS-232 remote functions are used to control of this product’s features. Features include input to outpu

15RS-232 SERIAL CONTROL COMMANDS#EDIDDSTOLO FunctionThe #EDIDDSTOLOfunction reads the downstream EDID and stores into all lo-cal inputs.Syntaxy:#EDIDD

16RS-232 SERIAL CONTROL COMMANDS#DDCTODS FunctionThe #DDCTODS function routes the input DDC to the downstream EDID (pass-through mode).Syntaxy:#DDCTOD

ASKING FOR ASSISTANCERev A6Technical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM

17RS-232 SERIAL CONTROL COMMANDS#LOEDIDTOBA FunctionThe #LOEDIDTOBA function loads the specifi ed EDID fi le and stores it in aspecifi ed EDID bank.Synta

18RS-232 SERIAL CONTROL COMMANDS#LOEDIDTOLO FunctionThe #LOEDIDTOLO function loads the specifi ed EDID fi le to a specifi ed localinput.Syntaxy:#LOEDIDTO

19RS-232 SERIAL CONTROL COMMANDS#PRDSEDID FunctionThe #PRDSEDID function reads the downstream EDID and sends it to the serial port.Syntaxy:#PRDSEDID p

20RS-232 SERIAL CONTROL COMMANDSCommandsSimplifi ed syntax was used for command implementation for faster operation withthe device: # character – isn’t

21RS-232 SERIAL CONTROL COMMANDS2. USING SHORT-CUT CHARACTERS TO CHANGE SETTINGS2.1 HYPERTERMINALtm SETTINGS in Microsoft WindowstmFirst, please setup

22Rear of unitFront of unitRack mount ears are provided for installation of this unit into a 1U rack mountspace.1.Locate the side screws on the unit.2

23SPECIFICATIONSVideo Amplifi er Bandwidth...165 MHz x 2Input Video Signal...

24Gefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects and Gefe

CONTENTS1 Introduction2 Operation Notes3 Features4 Panel Layout5 Panel Descriptions6 Connecting the 8x1 DVI KVM DL Switcher7 8x1 DVI KVM DL Remote D

20600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefen.com [email protected] A6PbThis product uses

1INTRODUCTIONCongratulations on your purchase of the 8x1 DVI KVM DL Switcher. Your complete satisfaction is very important to us.GefenGefen delivers i

2OPERATION NOTESREAD THESE NOTES BEFORE INSTALLING OROPERATING THE GEFEN 8X1 DVI KVM DL SWITCHER• The 8x1 DVI KVM DL Switcher will take any of up to e

3FEATURESFeatures• Switches between any eight dual link (or single link) DVI computers• Switches USB 2.0, keyboard, mouse, and analog audio•

4Back PanelPANEL LAYOUTFront Panel542136897101211

5PANEL DESCRIPTIONS1External IR PortFor connection of external IR extension device such as the Gefen IR Extender (part # EXT-RMT-EXTIR).2 IR ReceiverR

6CONNECTING THE 8X1 DVI KVM DL SWITCHERHow to Connect the 8x1 DVI KVM DL Switcher1.Connect your computers’ DVI, USB, and Audio sources to the 8x1 DVI